Search Results

The body stiffness plays a key role in vehicle performance, such as noise and vibration, ride and handling, durability and so on. In particular, a body D-pillar ring structure is the most sensitive affecting the body stiffness on vehicle with tail gate. Therefore, since D-pillar body ring structure for high stiffness and lightweight is required, an optimized design methodology that simultaneously satisfies the requirements was studied. It focused on a methodology that body engineering designers can optimize design parameters easily and quickly by themselves in the preceding stages of vehicle’s styling distribution and design conceptual planning. First, it is important to establish the body stiffness design strategy by predicting the body stiffness with the vehicle’s styling at early design stage. The methodology to predict body stiffness with the styling and body dimension specification parameters was introduced.

The purpose of this paper is to investigate the mixture formation and optimize the operating conditions under cold start in a stoichiometric (λ=1) GDI engine with wall-guided piston using a 3D commercial code, STAR-CD [8]. For GDI engine under cold start, it can be difficult to carry out the optimization of operating conditions by engine test alone without the understanding of mixture formation inside the combustion chamber. In this study, three cold start conditions of the catalyst heating mode with split injection, the cranking under freezing temperature and acceleration before engine warm-up which causes oil dilution were calculated. In particular, injection strategy for each cold start condition were optimized and compared to the engine test data. The previously validated spray models [6] were applied to the analysis of the spray formation and mixing process inside the combustion chamber.

In this study, the preliminary validation method of the steering system is constructed and the objective is to satisfy the target performance in the conceptual design stage for minimizing the problems after the detailed design. The first consideration about steering system is how to extract the reliable steering effort for parking. The tire model commonly used in MBD(Multi-Body Dynamics) has limited ability to represent deformations under heavy loads. Therefore, it is necessary to study adequate tire model to simulate the behavior due to the large deformation and friction between the ground and the tire. The two approaches related with F tire model and mathematical model are used. The second is how to extract each link’s load in the conceptual design stage. Until now, each link’s load could be derived only by actual vehicle test, and a durability analysis was performed using only pre-settled RIG test conditions.

Automotive OEMs have introduced a new development paradigm, modular architecture development, to improve diversity quality and production efficiency. It needs solid fundamentals of system-based performance evaluation and development for each system level and single component level. When it comes to NVH development, it is challenging to realize the modular concept because noise and vibration should be transferred through various transfer path consisting of many parts and systems, which interact with each other. It is challenging for a single system of interest to be evaluated independently of the adjacent parts and environments. In this study, a new system-based development process for a vehicle suspension was investigated by applying blocked force theory and FRF-based dynamic substructuring. The objective is to determine the better dynamic stiffness distribution of many bushes installed in a suspension system in the frequency range corresponding to road noise.

The automotive shock absorber has various functions in car performance. Particularly, it is a dominant tuning parameter to get good primary and secondary ride characteristics within 1-35Hz ranges in car development. Thus, understanding of characteristics of shock absorber in this frequency range is indispensable to both test and analysis engineers for an effective and systematic approach. In this study, tire is also investigated from the same point of view. Frequency dependent stiffness and damping coefficient are extracted by discrete sine swept test under constant velocity of 25, 50, 100mm/sec which represent typical road surface conditions[1]. The responses are analyzed on frequency domain and the basic theoretical background for this approach is introduced.

Lithium-ion battery has advantages of high energy density and cost effectiveness than other types of batteries. However due to the low mechanical stability, their performance is strongly influenced by environmental conditions. Especially, external pressure on a cell surface is a crucial factor because an appropriate force can improve battery cycle life, but excessive force may cause structural failure. In addition, battery pack is composed of various components so that uncertainties in dimension and material properties of each component can cause a wide variance in initial pressure. Therefore, it is important to optimize structural design of battery pack to ensure initial pressure in an effective range. In this paper, target stiffness of module structure was determined based on cell level cycle life test, then structural design has been optimized for weight reduction. Cell cycling tests were performed under different stiffness conditions and analyzed with regression model.

Applying BSM (Balance shaft module) is a very common and effective way to reduce the 2nd-order powertrain vibration which is caused by the ill-balanced inertia force due to the oscillating masses inside an engine. However, the adoption of a BSM can also produce undesirable things especially in cost, fuel economy, starting performance, and so on. Therefore, for small vehicles, in which case cost and weight are key factors at the development stage, it is often required to develop competitive NVH performance without the expensive apparatus like a BSM. In this paper, in order to develop interior noise and vibration of a 4-cylinder vehicle without a BSM, we analyzed the contribution of some transfer paths for powertrain vibration, and could reduce interior booming noise by tuning the dynamic characteristic of the engine mount which was one of the largest transfer paths.

The mobility technique is used to analyze the transfer functions of road noise between the suspension and the body structure. In the previous analyses, the suspension system and the body structure are altogether modeled as subsystems in the noise transfer path. In this paper, the mobility between the suspension and the body structure is analyzed by the dynamic stiffness at the connecting points. The measured drive point acceleration FRF at the connecting point in the transfer path was used to estimate the contributions of subsystems. The vibration modes of tire, the acoustic noise of tire's interior cavity, the vibration modes of the car's interior room, and the vibrations of body structure and the chassis are also considered to analyze the coupling effects of the road noise. Analyzing the measured results, direction for modification of car components is suggested.

In general, the ride and handling characteristics of a vehicle are strongly dependent on chassis parameters that come from the kinematic and compliance properties of a suspension system. For ride comfort improvement of a compact SUV with increasing handling performance simultaneously, this research proposes a new quantitative approach by considering various driving maneuvers and road surfaces. Particularly, five different road surfaces were used for ride comfort analysis, and this analysis was performed for two different vehicle speeds on a cleat road profile and three different vehicle speeds on a rough road profile. The contribution analysis of a suspension and a seat structure to ride comfort was investigated in order to decide an optimal structural combination. It was shown that contribution of each factor is different according to road profiles and driving conditions respectively.

Design for six sigma (DFSS) with sigma based robust design will have a major influence on the future design, if it is applied during the conceptual design phase or design change phase. DFSS will result in more improved but less expensive quality products. This paper presents the implementation of DFSS for robust design of a brake judder of heavy-duty trucks. The problem of brake judder is typically caused by quality defects in manufacturing. However this quality problem can't be controlled deterministically and requires a design considering the uncertainty. In this paper sigma based robust design methodology is applied to improve the brake judder quality problem at the last step of DFSS. Results between conventional deterministic optimization and the proposed sigma based robust design are compared. The robust design by DFSS shows that the manufacturing cost may increase as the quality level increase.

This paper introduces a systematic wiring guideline which includes coupling noise calculation, wire layout design, and wire type selection methodologies. The coupling theory between wires has been introduced long time ago but it was not successfully applied to real automotive wiring design due to the complexity in the theory such as large number of parameters and many different conditions in automotive wiring environment. In this paper, the complexity is reduced by separating physical parameters and electrical parameters and identifying controllable parameters and given parameters. This paper first introduces parameters which are used in the coupling equations and automotive wiring design, then the coupling noise calculation method which uses the coupling equations is introduced. The systematic automotive wiring guideline which prevents noise problem in various design stage such as system filter design, wire layout design, wire type selection is introduced.

This paper presents the development of the active geometry control suspension(AGCS) system as the world-first, unique and patented chassis technology, which has more advantages than the conventional active chassis control systems in terms of basic concept. The control approach of the conventional systems such as active suspensions(slow active, full active) and four wheel steering(4WS) system is directly to control the same direction with acting load to stabilize vehicle behavior resulting from external inputs, but AGCS controls the cause of vehicle behaviors occurring from vehicle and thus makes the system stable because it works as mechanical system after control action. The effect of AGCS is the remarkable enhancement of avoidance performance in abrupt lane change driving by controlling the rear bump toe geometry.

With the advent of cars with computerized engines, drivers sometimes suffer discomfort with “check engine” light problem, and as a result, insist on increasing levels of reliability in their cars. Hence, reliability of the wiring harness has become a very important automotive design characteristic. On one hand, the more secure an engine mounting system is, the more stable the engine wiring harness is. In order to enhance their durability, car manufacturers need to perform many validation tests during the development phase which involves a lot of time and cost. In this study, a newly developed lab-simulation test is proposed to qualify the design of engine mounting and engine wiring early in the design cycle and reduce time and expense. The lab-simulation test has contributed to a significant cost and time reduction and has shown good correlation to the original proving ground test.

In this paper, front and rear 5-link independent suspension systems are introduced which are developed for the Hyundai Genesis. The front suspension has two upper links, two lower links, and a tie-rod. In the rear suspension, there are two upper links, a lower link, a trailing link, and a toe control link. The design concepts of front and rear suspension systems are explained, respectively. Also, it is presented how the suspension characteristics are designed and optimized to satisfy the desired performances such as luxurious ride feeling and precise handling.

This paper investigates the sensitivity of stiffness of front and rear suspension systems on the structure-borne road noise inside a vehicle cabin. A flexible multi-body dynamics based approach is used to simulate the structural dynamics of suspension systems including rubber bushings, suspension arms, a subframe and a twist beam. This approach can accurately predict the force transfer to the trimmed body at each suspension mounting point up to a frequency range of 0 to 300 Hz, which is validated against a force measurement test using a suspension test rig. Predicted forces at each mounting point are converted to road noise inside the cabin by multiplying it with experimentally obtained noise transfer functions. All of the suspension components are modeled as flexible bodies using Craig-Bampton component mode synthesis method.

This paper introduces newly developed suspension system for the all-new SantaFe model of Hyundai Motor Company which will be on the market this year. The new suspension of the all-new SantaFe has been developed to give better handling and driving confidence to a driver compared to the previous model while maintaining a good ride experience. To achieve these targets, the suspension has been fully changed and finely adjusted. The compliance characteristics have been contrasted to those of the previous model. Also, the crash performance and package efficiency which are related to suspension layout has been considered without limitation of suspension performance. Based on the customer’s voice of market, the suspension of the newly developed SantaFe has tried to fit the various customer’s demands.

This paper presents an industrial application of the Analytical Target Cascading (ATC) methodology to the optimal design of commercial vehicle steering and suspension system. This is a pilot study about the suspension and steering design of a semi medium bus, whose objective is to develop and introduce an ATC methodology to an automobile development process. In the conventional process, it is difficult not only to find design variables which meet the target of Ride and Handling (R&H) performance using a detailed full car model, but also to figure out the interrelation between the vehicle and its subsystems. In this study, ATC methodology is used in order to obtain the optimal values such as geometric characteristics satisfying both the vehicle's R&H target and the subsystem (suspension and steering system) 's target.

This paper introduces a newly developed suspension system for new Elantra model of Hyundai Motor Company which will be on the market this year. The new chassis of Elantra has been developed to give more driving pleasure and confidence to a driver. To achieve these driving targets, the suspension has been changed and finely adjusted to achieve better ride and handling performance compared with the previous generation. Especially, a new multi-link suspension which has two upper links has been developed. The kinematics and compliance characteristics have been contrasted to those of the previous model. Also, the crashworthiness and package efficiency has been considered without limitation of suspension performance. Based on the customer's voice of market, the suspension of new Elantra has tried to fit the all kind of the customer's demand.

This paper introduces newly developed suspension system for new Sonata model of Hyundai Motor Company which will be on the market this year. The new chassis of Sonata has been developed to give more driving pleasure and confidence to a driver. To achieve these driving target, suspension has been changed and finely adjusted to achieve better ride and handling performance compared to previous generation. The kinematics and compliance characteristics have been contrasted to those of previous model. Also, the crashworthiness and package efficiency which related to suspension layout has been considered without limitation of suspension performance. Based on the customer’s voice of market, the suspension of new Sonata has tried to fit the all kind of the customer’s demand.

Despite the widespread adoption of lithium-ion batteries in various applications such as energy storage, concerns related to thermal management have been persisting, primarily due to the heat generated during their operation and the associated adverse effects on its efficiency, safety, and lifetime. Hence, the thermal characterization of lithium-ion batteries is essential for optimizing the layout of the battery cells for a pack design and the corresponding thermal management system. This study focuses on an experimental investigation of heat generation of Li-ion batteries under different operating conditions, including charge-discharge rates, ambient temperatures, states of charge, and compressive pressure. The experiments were conducted using a custom-designed multifunctional calorimeter, enabling precise measurement of the heat generation rate of the battery and the entropy coefficient. The measured results have shown a good match with the calculated heat generation rate.